Permatex® 81158 Black Silicone Adhesive Sealant, 3 Oz

Permatex® Black Silicone Adhesive Sealant (low odor formula) is a general purpose, single component, room temperature vulcanizing (RTV) compound, designed for the sealing of mechanical assemblies. Upon curing from the exposure to moisture in the air, this non-sagging paste forms a tough, flexible, waterproof seal of silicone rubber, which resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Note: Not recommended for engine gasketing applications or windshield installation.

• Low odor formula
• General-purpose
• Waterproof and flexible
• Seals, bonds, repairs, mends and secures glass, metal, plastics, fabric, vinyl, weather stripping and vinyl tops
• Protects and repairs electrical wiring
• May be applied to horizontal or vertical surfaces
• Temperature range -75°F to 450°F (-59°C to 232°C); resists water, weather, and vibration
• Carded.
• Windshields, door frames, electrical connections, seams and roofs, vinyl tops, weather stripping (Not recommended for engine gasket applications).
• Windshields, hatches, electrical connections, seams and roofs, vinyl tops, weather stripping.
• Low odor formula
• Easy application
• Applied to horizontal or vertical surfaces
• Superior adhesion and flexibility
• Waterproofs
• Insulates
• Unaffected by vibration
• Non-flammable
• Non-toxic
• Metal
• Glass
• Wood
• Most plastics (excluding polyethylene and polypropylene)
• Silicone resin
• Vulcanized silicone rubber
• Ceramics
• Natural and synthetic fibers
• Painted surfaces.
• Lens Housings
• Windshields (for sealing only; not for installation)
• Windows
• Door frames
• Housings and covers.
• Remove all previous material from mating surfaces.
• For best results, clean and dry all surfaces with a residue-free solvent.
• Cut nozzle to desired bead size, 1/16" to 1/4" in diameter. A 1/8" bead is usually sufficient for most applications.
• Remove cap, puncture tube or cartridge seal and attach extension nozzle.
• Apply a continuous and even bead of silicone to one surface
• Assemble parts immediately while silicone is still wet. Secure or tighten as required, avoiding excessive squeeze-out.
• Pressure should be applied to parts for 24 hours until the silicone is fully cured.
• Allow excess material to extend beyond the extension nozzle to cure, sealing and protecting the remaining product from moisture. For reuse, simply remove the cured product from the tip.
• Remove uncured product from parts and hand-tools with a dry cloth, if skinned over, break film with a dry cloth to remove as much as possible, and remove the remaining material with Permatex® Gasket Remover (not for use on painted surfaces) as previously stated.
• Clean hands with a dry cloth or Permatex® Fast Orange® hand cleaner.
• Extrusion rate @ 25 degree Celsius, (grams/min): >250
• Flash Point TCC, degree Celsius (degree Fahrenheit): >93 (>200)
• Permatex® Black Silicone Adhesive Sealant cures on exposure to moisture in the air. The product dries tack free in 1 hour and fully cures in 24 hours. Cure times will vary with temperature, humidity and gap.
• Tensile Strength, N/mm2 (psi)**: >1.2 (>170')
• Continuous, degree Celsius (degree Fahrenheit): -59 to 232 (-75 to 450)
• Intermittent, degree Celsius (degree Fahrenheit): -59 to 260 (-75 to 500)
• This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.
• Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8 to 28 degree Celsius (46 to 82 degree Fahrenheit) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container.

Free shipping on orders over $35. Usually ships within 24 hours.

Returns accepted within 30 days by mail. Return shipping is paid by the customer. See our refund policy.