Kilz® L204511 Water Based Kitchen & Bath Primer / Sealer / Stainblocke

KILZ® KITCHEN & BATH Primer is a water based primer-sealer-stainblocker that is specially designed for residential surfaces in high humidity, moisture and temperature environments such as kitchens, bathrooms, powder rooms and laundry rooms. It offers excellent adhesion to most interior surfaces and provides a sound anchor for paints. The enhanced mildew-resistant film protects the primer from mildew growth. Will also block most stains including felt marker, grease, ink, pencil, tannin and water stains. It is a fast drying, low odor, low VOC formula and is easy to clean with soap and water.

• Size: 1 Gallon
• Interior water-base
• High hide stainblocker; improves topcoat adhesion
• Excellent for moisture-prone areas
• Offers excellent adhesion to most interior surfaces and provides a sound anchor for paints
• Enhanced mildew-resistant film protects the primer from mildew growth
• Will block most stains including felt marker, grease, ink, pencil, tannin and water stains
• Mildew resistant finish
• Hides previous color
• Helps block light/med stains
• Promotes adhesion
• Seals porous surfaces.

Surface Preparation

• All surfaces must be clean, dry, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose or peeling paint, rust and all other foreign substances
• If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry
• Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface
• Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming
• Mold or Mildew Covered Surfaces: Any existing mold and/or mildew on the surface MUST be removed before priming or painting. Wash the area with a mildew remover, rinse with water and allow to dry before priming
• Masonry, Brick and Plaster: KILZ KITCHEN & BATH Primer may be used on clean, dry, aged masonry surfaces. New masonry must be allowed to cure (dry) at least 30 days before applying KILZ KITCHEN & BATH Primer

Application

• Eye protection is recommended. For spray applications, a small amount of water (no more than 1/2 pint per gallon) may be added. Do not thin for stainblocking applications
• Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C). Stir thoroughly before and occasionally during use. Apply using a brush, roller or sprayer
• Brush – High quality Nylon/Polyester
• Roller – High quality 3/8"-1/2" nap on smooth surfaces or 1/2"-3/4" nap on semi-rough or porous surfaces
• Airless spray – .017" - .021" tip / 60 mesh filter
• Prime the entire surface to ensure a uniform appearance of the topcoat
• Stainblocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating
• Tinting: KILZ KITCHEN & BATH Primer may be tinted with up to 2 ounces of universal colorant per gallon. Tinting to a lighter shade than the topcoat is recommended
• Coverage: 300 - 400 sq. ft. (27.87 - 37 m2) per gallon depending on application method and surface porosity

Dry Time at 77°F (25°C), 50% RH

• Dries to the touch in 30 minutes at 77°F (25°C) and 50% humidity
• Recoat or topcoat after 1 hour.

Clean Up & Disposal

• Clean equipment and paint spatters with warm, soapy water
• Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service
• If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal information contact your local household refuse collection service.