Permatex® 82194 Ultra Grey® Rigid High-Torque RTV Silicone Gasket Make

Permatex® Ultra silicones were developed to meet todays technology changes. Sensor-safe, low odor, noncorrosive. Outstanding oil resistance and joint movement tolerance. Eight times more flexible than cork/composite gaskets; three times more oil resistant than conventional silicones. Temperature range -65ºF to 500ºF (-54°C to 260°C) intermittent; resists auto and shop fluids and vibration. OEM specified.

• Size: 3.5 ounce
• Sensor-safe, low odor, noncorrosive
• Outstanding oil resistance and joint movement tolerance.
• Eight times more flexible than cork/composite gaskets
• Three times more oil resistant than conventional silicones
• Temperature range -65 degrees Fahrenheit to 500 degrees Fahrenheit (-54 degrees Celsius to 260 degrees Celsius) intermittent; resists auto and shop fluids and vibration
• Use for valve covers, oil pans, transmission pans, intake manifold end seals, timing covers, water pumps and thermostat housings, tube
• OEM Specified.

Product Benefits:

• High load resistance
• Improved oil resistance
• Sensor safe, non-corrosive
• Replaces most cut gaskets
• Can be used as a gasket maker or dressing
• Non-flammable, Non-toxic
• Low odor

Suggested Applications:

Automotive

• Valve covers, oil pans, transmission pans, intake manifold end seals, timing covers, water pumps, thermostat housings.

Heavy Duty

• Cover housing gasket, differential, assembly to rear axle housing, power dividers, axle shaft flanges.

Directions:

• For best results, clean and dry all surfaces with a residue-free solvent such as Permatex® Brake & Parts Cleaner.
• Cut nozzle to desired bead size. Gaskets are best formed using a 1/16" to 1/4" (2 to 6 mm) bead.
• Apply a continuous, even bead of silicone to one surface, surrounding all bolt holes. Assemble parts immediately while silicone is still wet. Finger tighten until material begins to squeeze out around flange. Allow to dry for one hour then retighten 1/4 to 1/2 turn.
• Silicone will skin over in one hour and fully cure in 24 hours under normal conditions. Allow more time for cold or very dry conditions. Clean uncured silicone from hands, tools and clothing with Permatex® Fast Orange® Wipes or Fast Orange® Hand Cleaner. NOTE: Not recommended for use on head gaskets or on parts in contact with gasoline.

Typical Applications:

• Valve covers
• Transmission pans
• Oil pans
• Timing gear covers
• Differential covers

Directions For Use:

For assembly as a form-in-place gasket

• Remove all previous material from mating surfaces. Permatex® Gasket Remover or Silicone Stripper is recommended for most materials.
• For best results, clean and dry all surfaces with a residue-free solvent, such as Permatex® Brake and Parts Cleaner.
• Cut nozzle to desired bead size, 1/16" to 1/4" in diameter. A 1/8" bead is usually sufficient for most applications.
• Remove cap, puncture tube or cartridge seal and attach extension nozzle.
• Apply a continuous and even bead of silicone to one surface, first tracing the internal areas of the gasket configuration, then all surrounding bolt holes.
• Assemble parts immediately while silicone is still wet. Secure or tighten to recommended torque specs.
• Re-torque will not be necessary after the product has cured.

For assembly as a gasket dressing

• Repeat steps 1 through 4 as in previous section.
• Apply a thin film of silicone to one surface to be sealed.
• Place the pre-cut gasket onto silicone film.
• Apply a second thin film to pre-cut gasket surface.
• Remove any excess and assemble parts immediately.

Note: Product is not recommended for use as a cylinder head gasket or head gasket sealant.